CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: SKGT4-12C hydraulic bar straightening cutting mach...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: SKGT4-12C hydraulic bar straightening cutting mach...:       SKGT4-12C hydraulic bar straightening cutting machine you want in the era of rapid development of technology...

SKGT4-12C hydraulic bar straightening cutting machine unique process

 SKGT4-12C hydraulic bar straightening cutting machine you want in the era of rapid development of technology to the occupation of a place, then it requires you to bend steel hoop factory settings develop better equipped to meet the market's satisfaction. While many construction process has reinforced these advanced cutting technology equipment set up, when placed on the site can only be regarded as a high-priced furnishings not have any effects. To this end it asked the relevant operator to have building works above the high school level of civilization than we can complete products processing, and low levels of seniority will not be possible to rationalize the operation of such a high technology content bending hoop machine equipment .

      Traditional processing level whenever the use of stirrups single disc at the end of round bar Britain modulation, intercept, bending hoop processes and distribute complete.

      The process is lagging behind, SKGT4-12C hydraulic bar straightening cutting machine can not meet modern requirements for parts of construction is also not up to the actual needs of the construction schedule. In a large number of waste of labor, take up more space, labor, low efficiency, serious fraudulent claims are stirrups dimensional accuracy and shape accuracy is poor.

      The device operating system can be controlled as much as any program can be fragmented ancient and modern shape and surface-type graphics 60 corners or less, can be stored on countless species differences over the shape of the product, and a store graphics library, so many kinds large quantities flooded out.

      SKGT4-12C hydraulic bar straightening cutting machine calculating machine ancestors receiving digital control, active bar straightening completed quickly, length, bending hoop, interception. High compliance rate machine can exchange 20-30 steel workers, within the context of full compliance with the steel hoop bending machine operations.

GW42E-Automatic (computer board) steel bending machine can stand up or lying down based on user usage

      GW42E-Automatic (computer board) steel bending machine can stand up use of the user or lying down, different molds can be customized according to user requirements. Bender variety, main structure has the following categories:
①: Press the bending roller of the division, there are three main rollers, four roll bending machine, three roll bending machine is divided into three roller symmetrical, asymmetrical three roller two kinds;
②: by the form of transmission can be divided into mechanical, hydraulic, mechanical and hydraulic hybrid;
③: GW42E-Automatic (computer board) steel bending machine Press control mode split, there are roller bits move the pointer display, digital display, NC control, CNC controls and machine control;
④: Press work roll movement forms division, there are three main roller raised type, Curve down, tilt down type, four roller four roller linear and arc-form bending machine.
      GW42E-Automatic (computer board) steel bending machine at home and abroad is more advanced profiles molding equipment, is widely used in petroleum, chemical, steel, machinery manufacturing and other industries a variety of circular flange production.

Master CNC steel models straightening techniques are very important

    Some novices in the use of CNC steel models for some time, will feel out of tune bending of reinforcement is not high. This is because some bending hoop wheel may appear loose, there may be considered misuse, leading to horizontal adjustment wheel, the rotational position of the intermediate bending hoop wheel deviation. If it is about bias, appropriate adjustments to some of the hoop bending machine cutting machine front end of the horizontal adjustment wheel so that the gap several intermediate wheels on the same line, after the adjustment, and then observed.    CNC steel models cut occurs constantly reinforced the case, you should check the following areas: the solenoid valve, exchanges and contacts, proximity switches and relays. One by one to check these parts need to be cleaned to clean up, if there is damage to be replaced, one by one investigation after another start running, it is possible to solve the bending hoop machine continue to cut steel case.   If the Big Bend, reinforced on the floor, obviously feeling can be bent, which it needs to adjust the rotation of the intermediate portion. Open the protective cover, adjust bending hoop wheel adjustment nut wrench reduce the gap between CNC steel models round. After adjusting the run, we can solve this problem.   Bending hoop machine is actually a simple and easy to operate, if you do routine maintenance is in place, but also in the work of past experience, it would be handy to use, it will be your assistant.

El uso yel mantenimiento de GT6-14A CNC Rebar

1, GT6-14A CNC Rebar debe estar familiarizado con el manual antes de comenzar, añadir el aceite de acuerdo con la normativa, compruebe si la dirección de cierre de apriete de rotación de la rueda de alambre se encuentra con la dirección predeterminada, encontrar problemas en el tiempo.

2 Verifique que la tuerca de alambre transversal está suelto en el cuchillo, el cuchillo corta la brecha de modulación cruzada y el cuchillo de corte vertical, tan pequeño como sea posible, pero no muy fuerte, es generalmente apropiado deslizante hacia arriba y abajo en el punzón y un cuchillo de corte vertical la brecha vertical es generalmente de 2-3 mm, el punzón superior con un cuchillo vertical de reducir la cantidad de presión es generalmente de 4-5 mm.

3, Tocar la mano de seda de la sensación pequeña después de Gt6-14a CNC Rebar, lo que indica que endereza ángulo dado, poner el ajuste de gasto más pequeño, si existe curvatura mayor, necesario ajustar el ángulo del molde se incrementa, si no es recta, alambre es necesario comprobar la velocidad de la rueda del rotor, y los agujeros de cuchillo transversales no es una posición horizontal, tres puntos deben alinearse, en torno al nivel no puede desviarse de.

4. Si aparece el cable roto, compruebe si la presión de la rueda de agarre alambre de resorte no es la ranura de la rueda apretada o desgastado hilo en un tanque grave, ajustado  alambre rueda de presión o no, tenemos que cambiar las ruedas de alambre ritmo.

5, Si hay un cable roto la cabeza rebabas, cortador de cable roto puede ser horizontal, posición vertical es demasiado grande, es necesario ajustar el intersticio de cuchilla horizontal y vertical, si no fuera suficiente, revise si la cuchilla horizontal y vertical desgaste serio, si muy desgastado, desanime el cortador de alambre vertical retirar y cortador de alambre transversal,Gt6-14a CNC Rebar de alambre en la rueda de aleación pulida transversal, cuchillo vertical de los alambres rotos en una rueda de molienda en general pulidos hasta afilada hasta el momento.

6, Si hay un corte continuo a través del resorte de tensión pueden ser enviados a ajustar la tensión del resorte de tensión, un muelle de compresión también podrán enviarse ruedas de alambreo, no empuje la pista necesita ajustar los rollitos de primavera de agarre. En pocas palabras, depende de la situación real.

Steel cutting equipment Description

 Rebar cutting apparatus including first and second discs carried by a shaft mounted on a frame. The discs are pivotable relative to each other and each includes grooves which can be aligned for receipt of a bar to be cut. The first discs is pivotal on a shaft carried by a frame and moves incrementally through a predetermined arc such that the grooves become substantially axially offset from each other.

 The appartus is attached to a manually operable bender and straightener having a linearly reciprocable slide mounted within a guideway. As the slide is reciprocated, the first and second discs of the apparatus are pivoted relative to each other. The apparatus includes a ratchet mechanism for allowing incremental pivoting of the discs relative to each other through the predetermined arc, while allowing reciprocable movement of the slide to its initial position without returning the first and second discs to the position in which the grooves are aligned. The apparatus also includes return means for pivotally returning the first discs in a second direction through the entire predetermined arc during a single return stroke of the slide. When the grooves are substantially axially offset from each other, a bar placed in the aligned groove is thereby cut.

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models can save steel

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models can save steel:     Today the building, number of floors, more and more buildings, more and higher quality requirements for building higher and higher in or...