CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar appearance quality and overall p...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar appearance quality and overall p...:    一、    Appearance Quality         GT6-14A CNC Rebar  shape should be nice, non-processing surface should be smooth, bolt tail exposed,...

GT6-14A CNC Rebar appearance quality and overall performance machine

   一、    Appearance Quality

       GT6-14A CNC Rebar shape should be nice, non-processing surface should be smooth, bolt tail exposed, the exposed length should not exceed 2-3mm.

       The exposed surface of the workpiece should be done anti-rust treatment.

       Painting should be firm, the coating should be uniform color, wrinkle-free skin, channeling, flow marks and other defects.

    二、   Overall performance

       Gt6-14a CNC Rebar idling noise should not exceed 80dB (A), load operating noise (excluding off instant reinforcement noise) should not exceed 85dB (A).

       Straightening and Cutting Machine reliability test time should not be less than 200h, allow industrial assessment methods. The average time between failures, GT6-14A CNC Rebarshould be greater than 150h, reliability should not be less than 90%

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Objective reasons GT6-14A CNC Rebar failure occurr...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Objective reasons GT6-14A CNC Rebar failure occurr...: The long-term research analysis, Gt6-14a CNC Rebar  equipment malfunction exists some objective reasons, and these reasons can be avoided. ...

Objective reasons GT6-14A CNC Rebar failure occurred

The long-term research analysis,Gt6-14a CNC Rebar equipment malfunction exists some objective reasons, and these reasons can be avoided. Such as

First, safety procedures inadequate or poor management, lack of basic training for the operator to cause GT6-14A CNC Rebar injury accidents occur
        ① operator do not follow safety rules and operations;
        ② not wearing appropriate protective clothing;
        ③ workpiece or tool is not holding firmly to start steel cutting machine.

Two, Gt6-14a CNC Rebar running in a non-normal state
        ① straightening machine design, manufacturing or installation defects;
        Function ② straightening machine parts, accessories and safety equipment failures;

Third, the workplace environment is not good
        ① workplace lighting is bad;
        ② temperature inappropriate, excessive noise;
        ③ equipment layout is unreasonable, as well as spare parts, semi-finished products piled irregular and the like;
        ④ process planning and process equipment do not meet safety requirements, the lack of necessary safety measures.

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models reinforced straighten cutter leng...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models reinforced straighten cutter leng...: In order to achieve  CNC steel models and thread steel straightening machine of numerical control, automation, accurate measurement must be ...

CNC steel models reinforced straighten cutter length detection

In order to achieve CNC steel modelsand thread steel straightening machine of numerical control, automation, accurate measurement must be reinforced according to the length of the required length automatically cut reinforcement. In this paper, these two questions relative error were studied, and in my school Machinery Factory production of steel straightening and cutting machine and achieved satisfactory results, cutting steel is less than 0.5%, to overcome the existing equipment can not be used for small-diameter steel tone straight and cutting question. The device has an automatic length detection, automatic synchronization of the mobile station under the knife, cut the number of steel automatic counting and other functions.

       1, CNC steel modelsworks Figure 1 is reinforced straighten cutter of the mechanical drive schematic. It is transferred straight bars 1 in 2 and traction drive roller 4 feed rollers under a rotating tune straight 3 straight. Reinforced straight through after the upper and lower turret of the port to move forward. When the front end reinforcement after straightening iron is not moved to stop position 7, 8 hammer inertia wheel drive although mainly as vertical reciprocating movement 9, but due to not come into contact with the knife station 10, it is not subjected to shear reinforcement. When the front straight after the steel top to 7:00 stopper by the lever 6 causes the upper turret 10, lower turret 5 is moved forward. At this point, the reciprocating motion of the hammer 8 through the upper and lower turrets of reinforced shear (shear reinforcement length L), completed a steel straightening and cutting. Continuous motion, to complete the continuous steel straightening and cutting.
       2, reinforced length detection CNC steel models harsh working conditions, larger vibration machines work. Upon detecting a bar size, in addition to ensuring accuracy, but also must meet anti-interference ability, reliable, long life and other requirements. Existing reinforced straighten cutter size detection machine adopts contact measurement, that is, when reinforced move, driven by resilient friction wheel rotation. Friction wheel and then connected with the pulse generator, calculate bar length by the count value of the pulse generator. Due to straighten cutter work in the machine itself and reinforced vibration is very strong, wear friction wheel is extremely serious, if from time to time to replace the friction wheel is detected, it will affect the detection accuracy, resulting in cutting errors. For these reasons, reinforced length detection method must be used for non-contact detection. By trials comparing the use of applied magnetic signal on reinforcement alternately programs more feasible, meet the design requirements.
 

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar construction Use Straightening M...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar construction Use Straightening M...: GT6-14A CNC Rebar    construction Use: Debugging CNC hydraulic steel straightening machine is a critical step in the formal operation of th...

GT6-14A CNC Rebar construction Use Straightening Machine

GT6-14A CNC Rebar  construction Use: Debugging CNC hydraulic steel straightening machine is a critical step in the formal operation of the device, future steel production process, has underestimated the role of, but the reality is that many enterprises in order to rush to production, one-sided pursuit of economic efficiency and not enough emphasis on this key measure, and then planted a lot of hidden dangers for the subsequent operation, here we explore simple steel straightening and cutting machine debugging requirements. Installation GT6-14A CNC Rebar, the first should be maintained on a relatively flat ground, it is best to put some cushion, you can prevent the machine at high speed when and ground vibrate. Host connectivity and the best runner on the same straight line, check whether the punch and bite off, if you do not bite it, adjust the height of the lower pulley to slide inside slider transferred to the desired size, and then use the screws fixed. When debugging GT6-14A CNC Rebar  straighten opportunity to bend the wire phenomenon, you can adjust the angle of straight down the block to see if and straightening device, the pressure roll groove in a straight line. Yarn breakage encountered, we should first check to see if the straight block angle is too large, or the knife does not return back, spring wire roll on too loose, the material is not good and so on. When the machine has run wire phenomenon, related operations personnel necessary to check whether the pressure roller spring too tight, too loose tension spring slide, or slide below Ganggun dragline silk is not in place, the slide does not slide. In specific debugging GT6-14A CNC Rebar process, the operator should strictly check the electrical circuit wiring is correct, each operating point and stop control are normal and reliable. After straightening adjustments within straight rotations, with particular attention to the adjustment lock nut on the bolt without loosening, and close the safety cover, before starting the motor.

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine, the need for constructio...

Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine, the need for constructio...: What is  Portable Cutting Machine ? In fact, it is cutting equipment, primarily for cutting steel, meets the requirements of the job. Many p...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models's precautions

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models's precautions: First, check  CNC steel models  mechanical performance is good, the table and the table to maintain the level bending machine; and ready for...

CNC steel models's precautions

First, check CNC steel models mechanical performance is good, the table and the table to maintain the level bending machine; and ready for all kinds of mandrel tool block.

Second, according to the diameter and bending hoop machines installed rebar processing requirements mandrel forming axis, iron shaft gear or a variable fences, mandrel diameter should be 2.5 times the bar diameter.

Third, check the mandrel, the stopper, the turntable should be no damage and cracks, securing reliable shield, confirm normal machine operation by air before the operation.

Fourth, when the job will need to bend rebar inserted in one end of the fixed turntable with a gap, and the other end is fixed and hand pressed against the body, inspection body fixed, and indeed on the side of safety before starting block reinforcement.

Five non-replacement of jobs and change the angle of the mandrel and the governor and other operations, nor refueling or removal.

Sixth, bending steel, non-processed CNC steel models machines for the specified rebar diameter, root number and mechanical speed.

Seven high bending stiffness or low alloy steel, machinery nameplate should be a maximum limit for standard diameter, and replace the corresponding spindle.

Eight, prohibited within the operating radius of curved steel and the body does not have a fixed side stop people. Curved good semi-finished products should be stacked neatly, hooks shall not be upward.

Nine, turntable commutation, must be carried out after it stops.

Ten, the job is finished, clean up the site, maintenance CNC steel models, power lockbox