CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...:          GT6-14A CNC Rebar  working environment is very dangerous, so steel straightening machine operation must be strict, safe operation....

GT6-14A CNC Rebar operation to seize the main points, ensure safety in production

        GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation.
First, according to the bar diameter straight tone, choose the appropriate straightening block, entrainment wheel slots and drive speed. Straightening block aperture is larger than the bar diameter should be 2 ~ 5mm, the same width and the traction wheel straightening bar diameter.
Second, straightening adjustment block. Within the general tone straight five straight blocks, the first of two straight blocks 1,5 shall be placed in the line will be in the middle of the three may be offset from the centerline. First make steel offset about 3mm offset through test tone, such as reinforced still slow corners, gradually increase the offset until straightening up.
Third, cut three or four bars need to stop after checking the length is appropriate, subject to bias, adjustable limit switches or length plate, until the appropriate date.
Fourth, in the front portion of the guide tube should be installed about 1 meter steel one. GT6-14A CNC Rebar should be transferred through the first pipe, and then penetrate the guide tube and transfer straight to prevent pop wounding nearly every dish reinforced straight when finished.
Fifth, the straightening block is not fixed, the shield is not covered before, can not penetrate reinforced in order to prevent the switch on the machine, straight block flying wounding.
Sixth, the machine allowed to pile up objects to prevent mechanical vibration objects have fallen into the body. Reinforced load pressure roller, hand drum should maintain a certain distance, the drum machine operation shall not be adjusted, non-gloved hands.
Seven GT6-14A CNC Rebar is not adjusted until the end, people have to escape, wounding prevent swinging. Shorter than 2m or larger in diameter than steel straightening 9mm should low speed processing.

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models positioning device supporting cha...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models positioning device supporting cha...:        CNC steel models  reinforced the positioning support means, including the lifting cylinder, positioning the support structure, the su...

CNC steel models positioning device supporting characteristics

      CNC steel models reinforced the positioning support means, including the lifting cylinder, positioning the support structure, the support structure of the positioning by the auxiliary support block, positioning the support block and the guide blocks, auxiliary support block in working condition relatively steel bending machine folder handpiece fixed relative to the guide block CNC steel models folder handpiece fixed guide block vertically concave guide grooves or guide holes, positioning the support block slidably disposed in the concave guide grooves or guide holes, the lift cylinder located in the positioning support bottom block, the lifting cylinder piston rod acts on the lower end of the positioning of the support block, forcing the positioning of the support block to move upward along the concave guide grooves or guide hole, the upper end of the positioning of the support block is provided with positioning faces were pressed to deal with curved bars positioning. The solution to the existing rebar positioning support device positioned support block as a whole, need to be completely replaced when damaged,CNC steel models and because the role of arm longer need to use the larger cylinder, the higher cost.

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar inexhaustible power

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar inexhaustible power:       We produce  GT6-14A CNC Rebar , straight steel surface after almost no scratches, good straightness, longitudinal diameter not twist,...

GT6-14A CNC Rebar inexhaustible power

      We produce GT6-14A CNC Rebar, straight steel surface after almost no scratches, good straightness, longitudinal diameter not twist, small strength loss, cut off a small error, a simple, easy to adjust, blanking and simple, high production efficiency. Reinforced straighten cutter with bending hoop machine, extending machine synthesis stirrups production line can play a greater role in building production.
      Yongyi Tongfeng production of Gt6-14a CNC Rebar with a reasonable structure, easy to operate safe and reliable, suitable for cages, rabbit cage, construction mesh, all kinds of wire, Reinforcing insert wire cut off and shaped with wire mesh straightening.
      The aircraft structure is composed of high-speed rotation of the rotor angle adjustment straight wire mold, to straighten effect, then forward through the hundred hundred wire wire wheels. After reaching the required size, after the wire hit the runway to locate key advance forward 5 mm above the punch pressed immediately cut vertical strips knife, wire cutter through the vertical wire on the plate to suppress open bearings, Gt6-14a CNC Rebar wire off automatically to Tuosi frame, if you want to change the length, the mobile positioning keys.

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar level of prices and choice

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar level of prices and choice:     Users select the machine, first look at their own processing capacity, processing capacity if, in their own economic conditions permitt...

GT6-14A CNC Rebar level of prices and choice

    Users select the machine, first look at their own processing capacity, processing capacity if, in their own economic conditions permitting, should try to choose a high degree of automation of the machine, so to make money on the very fast speed, Gt6-14a CNC Rebar's cost is fast to recover. Yongyi Tongfeng recommend that you go to a regular mall to buy reinforced straighten cutter, you can see the kind, visually compare, look for the brand, etc., to prevent fraud.

    Specifically, reinforced straighten cutter There are many, according to the performance of different devices have tens of thousands to hundreds of thousands of dollars. Corresponding to the high price of the machine is highly automated, high speed, high efficiency, high quality, low energy consumption. Machine biggest difference is that the low-cost low degree of automation, labor intensity is very high, the corresponding output is low, the high cost. Because the larger the price difference different machines, so GT6-14A CNC Rebar to a reasonable choice according to need, the main reference data that is output.

    For example, a small construction site use, is characterized by a relatively small amount of steel, this machine choose the high price is a waste, on the market for reference prices around each million. If a greater amount of processing, such as large construction site or make it is necessary to choose a high degree of automation equipment used in steel processing center, the speed of these devices is very fast, low processing out of this machine steel costs, lower wage costs, sell for the same price, profits much higher than for small devices to be, so it is money very fast speed, high-yield high profits ×> × yield low profits. This price of the machine on the market are generally in the million or more, if matched with a more advanced set of automatic feeding equipment, the price is higher, and generally make steel processing center machines are generally in the million or more, according to the adjustable bar diameter Different prices will have a relatively large change, of course, large diameter GT6-14A CNC Rebar corresponding high price. There is also a machine that can roll on the round thread, were followed closely by straight cutting, this machine is the mainstream machining centers, its price is higher than the simple straight confidential tone.

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...:         GT6-14A CNC Rebar  working environment is very dangerous, so steel straightening machine operation must be strict, safe operation. ...

GT6-14A CNC Rebar operation to seize the main points

       GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation.
First, according to the bar diameter straight tone, choose the appropriate straightening block, entrainment wheel slots and drive speed. Straightening block aperture is larger than the bar diameter should be 2 ~ 5mm, the same width and the traction wheel straightening bar diameter.
Second, straightening adjustment block. Within the general tone straight five straight blocks, the first of two straight blocks 1,5 shall be placed in the line will be in the middle of the three may be offset from the centerline. First make steel offset about 3mm offset through test tone, such as reinforced still slow corners, gradually increase the offset until straightening up.
Third, cut three or four bars need to stop after checking the length is appropriate, subject to bias, adjustable limit switches or length plate, until the appropriate date.
Fourth, in the front portion of the guide tube should be installed about 1 meter steel one.Gt6-14a CNC Rebar should be transferred through the first pipe, and then penetrate the guide tube and transfer straight to prevent pop wounding nearly every dish reinforced straight when finished.
Fifth, the straightening block is not fixed, the shield is not covered before, can not penetrate reinforced in order to prevent the switch on the machine, straight block flying wounding.
Sixth, the machine allowed to pile up objects to prevent mechanical vibration objects have fallen into the body. Reinforced load pressure roller, hand drum should maintain a certain distance, the drum machine operation shall not be adjusted, non-gloved hands.
Seven, Gt6-14a CNC Rebar is not adjusted until the end, people have to avoid, prevent swinging wounding. Shorter than 2m or larger in diameter than steel straightening 9mm should low speed processing.

GT6-14A CNC Rebar operator safety precautions

1.GT6-14A CNC Rebar must be operated by hand. The operator must go through specialized security knowledge assessment, certificates after passing the examination. Mechanical installation should be solid stable, horizontal position. Fixed machinery should be a reliable basis; when moving mechanical work wedged tight walking round.
2. Mechanical prohibited ill job, find fault must be immediately shut down, turn off the power, by a professional mechanical maintenance man responsible for maintenance must assign someone to monitor mechanical maintenance. You must set the anti-smashing, rain hangar beside the machine should have piled raw materials, semi venues.
3. Longer bars during processing, should be someone helping, and obey the command of the operator, shall be arbitrarily sliding.
4. Feeder, the trough should be installed straight, and should be aligned with the guide tube, and the lower knife adjusting centerline straight holes.
5. After applying hand turn the flywheel to check the drive mechanism and the working device, adjust the gap, tightening bolts, confirm normal, start air operation, and no abnormal noise should check the bearings, gears meshing well, after operating normally before the job.
6. Gt6-14a CNC Rebar Should straighten rebar diameter, choose the appropriate straightening blocks and transmission speed. Aperture straightening block should Reinforced big 2 ~ 5mm, transmission speed should be chosen depending on the diameter, larger diameter should use slow, after debugging qualified before feeding.
7. In straightening block is not fixed, the front shield cover shall not feed. The job is strictly prohibited open the protective cover and adjust the gap ministries.
8. When Gt6-14a CNC Rebar is fed, hand and drag wheel should maintain a certain distance, can not close.
9. Before feeding, should not straight steel tip resection. Guide tube should be installed before a 1m long steel pipe, steel pipe and then should be fed straight through the front of the guide hole.

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models should be cleaned

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models should be cleaned: First, wash and clean-up. As a steel processing equipment,  CNC steel models  using  undoubtedly will leave some residual steel scrap, so af...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Mechanical CNC steel models structure optimization...

CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Mechanical CNC steel models structure optimization...: CNC steel models  in the use of the urgent need to support the body as a machine, that is, roughly said body of steel bending machine. Coate...

Mechanical CNC steel models structure optimization

CNC steel models in the use of the urgent need to support the body as a machine, that is, roughly said body of steel bending machine. Coated with a layer of special coating, not only beautify a good surface on the surface of the machine the machine, while the machine surface of the metal is a good protection.
Usually used when the machine needs to be well maintained, each time without the use of the residual trivial machine for cleaning above, guarantee the next time you use when not disturbed. In machine maintenance when the machine circuit checks, check the circuit breaker has no short circuit condition.
CNC steel models structure in the design were fully optimized, excellent principle guarantees the usual use of the machine, for the user, when using the machine need to follow relevant procedures and operating processes. in use when CNC steel models needs to pay attention to safety measures in place to avoid security risks.

CNC steel models should be cleaned

First, wash and clean-up. As a steel processing equipment, CNC steel models using  undoubtedly will leave some residual steel scrap, so after using the need to develop a good habit, it is timely for the various machines are devices to clean up. So as not to be disturbed in the future use of the process. At the same time when the device is not used to carry out the necessary cleanup is particularly important, including the use of necessary damp cloth with neutral detergent to clean the surface of the device, remove stains and dirt on top of the machine, to avoid the prolonged impact of the machine appearance and performance. In the clean-up time, especially for the interior of CNC steel models and a number of blind spots clean.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check CNC steel models is a regular process that requires a dedicated time to maintenance.