图片
2015年12月31日星期四
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...: GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation....
GT6-14A CNC Rebar operation to seize the main points, ensure safety in production
GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation.
First, according to the bar diameter straight tone, choose the appropriate straightening block, entrainment wheel slots and drive speed. Straightening block aperture is larger than the bar diameter should be 2 ~ 5mm, the same width and the traction wheel straightening bar diameter.
Second, straightening adjustment block. Within the general tone straight five straight blocks, the first of two straight blocks 1,5 shall be placed in the line will be in the middle of the three may be offset from the centerline. First make steel offset about 3mm offset through test tone, such as reinforced still slow corners, gradually increase the offset until straightening up.
Third, cut three or four bars need to stop after checking the length is appropriate, subject to bias, adjustable limit switches or length plate, until the appropriate date.
Fourth, in the front portion of the guide tube should be installed about 1 meter steel one. GT6-14A CNC Rebar should be transferred through the first pipe, and then penetrate the guide tube and transfer straight to prevent pop wounding nearly every dish reinforced straight when finished.
Fifth, the straightening block is not fixed, the shield is not covered before, can not penetrate reinforced in order to prevent the switch on the machine, straight block flying wounding.
Sixth, the machine allowed to pile up objects to prevent mechanical vibration objects have fallen into the body. Reinforced load pressure roller, hand drum should maintain a certain distance, the drum machine operation shall not be adjusted, non-gloved hands.
Seven GT6-14A CNC Rebar is not adjusted until the end, people have to escape, wounding prevent swinging. Shorter than 2m or larger in diameter than steel straightening 9mm should low speed processing.
2015年12月29日星期二
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models positioning device supporting cha...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models positioning device supporting cha...: CNC steel models reinforced the positioning support means, including the lifting cylinder, positioning the support structure, the su...
CNC steel models positioning device supporting characteristics
CNC steel models reinforced the positioning support means, including the lifting cylinder, positioning the support structure, the support structure of the positioning by the auxiliary support block, positioning the support block and the guide blocks, auxiliary support block in working condition relatively steel bending machine folder handpiece fixed relative to the guide block CNC steel models folder handpiece fixed guide block vertically concave guide grooves or guide holes, positioning the support block slidably disposed in the concave guide grooves or guide holes, the lift cylinder located in the positioning support bottom block, the lifting cylinder piston rod acts on the lower end of the positioning of the support block, forcing the positioning of the support block to move upward along the concave guide grooves or guide hole, the upper end of the positioning of the support block is provided with positioning faces were pressed to deal with curved bars positioning. The solution to the existing rebar positioning support device positioned support block as a whole, need to be completely replaced when damaged,CNC steel models and because the role of arm longer need to use the larger cylinder, the higher cost.
2015年12月23日星期三
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar inexhaustible power
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar inexhaustible power: We produce GT6-14A CNC Rebar , straight steel surface after almost no scratches, good straightness, longitudinal diameter not twist,...
2015年12月22日星期二
GT6-14A CNC Rebar inexhaustible power
We produce GT6-14A CNC Rebar, straight steel surface after almost no scratches, good straightness, longitudinal diameter not twist, small strength loss, cut off a small error, a simple, easy to adjust, blanking and simple, high production efficiency. Reinforced straighten cutter with bending hoop machine, extending machine synthesis stirrups production line can play a greater role in building production.
Yongyi Tongfeng production of Gt6-14a CNC Rebar with a reasonable structure, easy to operate safe and reliable, suitable for cages, rabbit cage, construction mesh, all kinds of wire, Reinforcing insert wire cut off and shaped with wire mesh straightening.
The aircraft structure is composed of high-speed rotation of the rotor angle adjustment straight wire mold, to straighten effect, then forward through the hundred hundred wire wire wheels. After reaching the required size, after the wire hit the runway to locate key advance forward 5 mm above the punch pressed immediately cut vertical strips knife, wire cutter through the vertical wire on the plate to suppress open bearings, Gt6-14a CNC Rebar wire off automatically to Tuosi frame, if you want to change the length, the mobile positioning keys.
2015年12月17日星期四
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar level of prices and choice
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar level of prices and choice: Users select the machine, first look at their own processing capacity, processing capacity if, in their own economic conditions permitt...
GT6-14A CNC Rebar level of prices and choice
Users select the machine, first look at their own processing capacity, processing capacity if, in their own economic conditions permitting, should try to choose a high degree of automation of the machine, so to make money on the very fast speed, Gt6-14a CNC Rebar's cost is fast to recover. Yongyi Tongfeng recommend that you go to a regular mall to buy reinforced straighten cutter, you can see the kind, visually compare, look for the brand, etc., to prevent fraud.
Specifically, reinforced straighten cutter There are many, according to the performance of different devices have tens of thousands to hundreds of thousands of dollars. Corresponding to the high price of the machine is highly automated, high speed, high efficiency, high quality, low energy consumption. Machine biggest difference is that the low-cost low degree of automation, labor intensity is very high, the corresponding output is low, the high cost. Because the larger the price difference different machines, so GT6-14A CNC Rebar to a reasonable choice according to need, the main reference data that is output.
For example, a small construction site use, is characterized by a relatively small amount of steel, this machine choose the high price is a waste, on the market for reference prices around each million. If a greater amount of processing, such as large construction site or make it is necessary to choose a high degree of automation equipment used in steel processing center, the speed of these devices is very fast, low processing out of this machine steel costs, lower wage costs, sell for the same price, profits much higher than for small devices to be, so it is money very fast speed, high-yield high profits ×> × yield low profits. This price of the machine on the market are generally in the million or more, if matched with a more advanced set of automatic feeding equipment, the price is higher, and generally make steel processing center machines are generally in the million or more, according to the adjustable bar diameter Different prices will have a relatively large change, of course, large diameter GT6-14A CNC Rebar corresponding high price. There is also a machine that can roll on the round thread, were followed closely by straight cutting, this machine is the mainstream machining centers, its price is higher than the simple straight confidential tone.
2015年12月15日星期二
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...: GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation. ...
GT6-14A CNC Rebar operation to seize the main points
GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation.
First, according to the bar diameter straight tone, choose the appropriate straightening block, entrainment wheel slots and drive speed. Straightening block aperture is larger than the bar diameter should be 2 ~ 5mm, the same width and the traction wheel straightening bar diameter.
Second, straightening adjustment block. Within the general tone straight five straight blocks, the first of two straight blocks 1,5 shall be placed in the line will be in the middle of the three may be offset from the centerline. First make steel offset about 3mm offset through test tone, such as reinforced still slow corners, gradually increase the offset until straightening up.
Third, cut three or four bars need to stop after checking the length is appropriate, subject to bias, adjustable limit switches or length plate, until the appropriate date.
Fourth, in the front portion of the guide tube should be installed about 1 meter steel one.Gt6-14a CNC Rebar should be transferred through the first pipe, and then penetrate the guide tube and transfer straight to prevent pop wounding nearly every dish reinforced straight when finished.
Fifth, the straightening block is not fixed, the shield is not covered before, can not penetrate reinforced in order to prevent the switch on the machine, straight block flying wounding.
Sixth, the machine allowed to pile up objects to prevent mechanical vibration objects have fallen into the body. Reinforced load pressure roller, hand drum should maintain a certain distance, the drum machine operation shall not be adjusted, non-gloved hands.
Seven, Gt6-14a CNC Rebar is not adjusted until the end, people have to avoid, prevent swinging wounding. Shorter than 2m or larger in diameter than steel straightening 9mm should low speed processing.
2015年12月12日星期六
GT6-14A CNC Rebar operator safety precautions
1.GT6-14A CNC Rebar must be operated by hand. The operator must go through specialized security knowledge assessment, certificates after passing the examination. Mechanical installation should be solid stable, horizontal position. Fixed machinery should be a reliable basis; when moving mechanical work wedged tight walking round.
2. Mechanical prohibited ill job, find fault must be immediately shut down, turn off the power, by a professional mechanical maintenance man responsible for maintenance must assign someone to monitor mechanical maintenance. You must set the anti-smashing, rain hangar beside the machine should have piled raw materials, semi venues.
3. Longer bars during processing, should be someone helping, and obey the command of the operator, shall be arbitrarily sliding.
4. Feeder, the trough should be installed straight, and should be aligned with the guide tube, and the lower knife adjusting centerline straight holes.
5. After applying hand turn the flywheel to check the drive mechanism and the working device, adjust the gap, tightening bolts, confirm normal, start air operation, and no abnormal noise should check the bearings, gears meshing well, after operating normally before the job.
6. Gt6-14a CNC Rebar Should straighten rebar diameter, choose the appropriate straightening blocks and transmission speed. Aperture straightening block should Reinforced big 2 ~ 5mm, transmission speed should be chosen depending on the diameter, larger diameter should use slow, after debugging qualified before feeding.
7. In straightening block is not fixed, the front shield cover shall not feed. The job is strictly prohibited open the protective cover and adjust the gap ministries.
8. When Gt6-14a CNC Rebar is fed, hand and drag wheel should maintain a certain distance, can not close.
9. Before feeding, should not straight steel tip resection. Guide tube should be installed before a 1m long steel pipe, steel pipe and then should be fed straight through the front of the guide hole.
2. Mechanical prohibited ill job, find fault must be immediately shut down, turn off the power, by a professional mechanical maintenance man responsible for maintenance must assign someone to monitor mechanical maintenance. You must set the anti-smashing, rain hangar beside the machine should have piled raw materials, semi venues.
3. Longer bars during processing, should be someone helping, and obey the command of the operator, shall be arbitrarily sliding.
4. Feeder, the trough should be installed straight, and should be aligned with the guide tube, and the lower knife adjusting centerline straight holes.
5. After applying hand turn the flywheel to check the drive mechanism and the working device, adjust the gap, tightening bolts, confirm normal, start air operation, and no abnormal noise should check the bearings, gears meshing well, after operating normally before the job.
6. Gt6-14a CNC Rebar Should straighten rebar diameter, choose the appropriate straightening blocks and transmission speed. Aperture straightening block should Reinforced big 2 ~ 5mm, transmission speed should be chosen depending on the diameter, larger diameter should use slow, after debugging qualified before feeding.
7. In straightening block is not fixed, the front shield cover shall not feed. The job is strictly prohibited open the protective cover and adjust the gap ministries.
8. When Gt6-14a CNC Rebar is fed, hand and drag wheel should maintain a certain distance, can not close.
9. Before feeding, should not straight steel tip resection. Guide tube should be installed before a 1m long steel pipe, steel pipe and then should be fed straight through the front of the guide hole.
2015年12月11日星期五
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models should be cleaned
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models should be cleaned: First, wash and clean-up. As a steel processing equipment, CNC steel models using undoubtedly will leave some residual steel scrap, so af...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Mechanical CNC steel models structure optimization...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Mechanical CNC steel models structure optimization...: CNC steel models in the use of the urgent need to support the body as a machine, that is, roughly said body of steel bending machine. Coate...
2015年12月10日星期四
Mechanical CNC steel models structure optimization
CNC steel models in the use of the urgent need to support the body as a machine, that is, roughly said body of steel bending machine. Coated with a layer of special coating, not only beautify a good surface on the surface of the machine the machine, while the machine surface of the metal is a good protection.
Usually used when the machine needs to be well maintained, each time without the use of the residual trivial machine for cleaning above, guarantee the next time you use when not disturbed. In machine maintenance when the machine circuit checks, check the circuit breaker has no short circuit condition.
CNC steel models structure in the design were fully optimized, excellent principle guarantees the usual use of the machine, for the user, when using the machine need to follow relevant procedures and operating processes. in use when CNC steel models needs to pay attention to safety measures in place to avoid security risks.
Usually used when the machine needs to be well maintained, each time without the use of the residual trivial machine for cleaning above, guarantee the next time you use when not disturbed. In machine maintenance when the machine circuit checks, check the circuit breaker has no short circuit condition.
CNC steel models structure in the design were fully optimized, excellent principle guarantees the usual use of the machine, for the user, when using the machine need to follow relevant procedures and operating processes. in use when CNC steel models needs to pay attention to safety measures in place to avoid security risks.
2015年12月3日星期四
CNC steel models should be cleaned
First, wash and clean-up. As a steel processing equipment, CNC steel models using undoubtedly will leave some residual steel scrap, so after using the need to develop a good habit, it is timely for the various machines are devices to clean up. So as not to be disturbed in the future use of the process. At the same time when the device is not used to carry out the necessary cleanup is particularly important, including the use of necessary damp cloth with neutral detergent to clean the surface of the device, remove stains and dirt on top of the machine, to avoid the prolonged impact of the machine appearance and performance. In the clean-up time, especially for the interior of CNC steel models and a number of blind spots clean.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check CNC steel models is a regular process that requires a dedicated time to maintenance.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check CNC steel models is a regular process that requires a dedicated time to maintenance.
2015年11月26日星期四
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar appearance quality and overall p...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar appearance quality and overall p...: 一、 Appearance Quality GT6-14A CNC Rebar shape should be nice, non-processing surface should be smooth, bolt tail exposed,...
GT6-14A CNC Rebar appearance quality and overall performance machine
一、 Appearance Quality
GT6-14A CNC Rebar shape should be nice, non-processing surface should be smooth, bolt tail exposed, the exposed length should not exceed 2-3mm.
The exposed surface of the workpiece should be done anti-rust treatment.
Painting should be firm, the coating should be uniform color, wrinkle-free skin, channeling, flow marks and other defects.
二、 Overall performance
Gt6-14a CNC Rebar idling noise should not exceed 80dB (A), load operating noise (excluding off instant reinforcement noise) should not exceed 85dB (A).
Straightening and Cutting Machine reliability test time should not be less than 200h, allow industrial assessment methods. The average time between failures, GT6-14A CNC Rebarshould be greater than 150h, reliability should not be less than 90%
2015年11月19日星期四
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Objective reasons GT6-14A CNC Rebar failure occurr...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Objective reasons GT6-14A CNC Rebar failure occurr...: The long-term research analysis, Gt6-14a CNC Rebar equipment malfunction exists some objective reasons, and these reasons can be avoided. ...
Objective reasons GT6-14A CNC Rebar failure occurred
The long-term research analysis,Gt6-14a CNC Rebar equipment malfunction exists some objective reasons, and these reasons can be avoided. Such as
First, safety procedures inadequate or poor management, lack of basic training for the operator to cause GT6-14A CNC Rebar injury accidents occur
① operator do not follow safety rules and operations;
② not wearing appropriate protective clothing;
③ workpiece or tool is not holding firmly to start steel cutting machine.
Two, Gt6-14a CNC Rebar running in a non-normal state
① straightening machine design, manufacturing or installation defects;
Function ② straightening machine parts, accessories and safety equipment failures;
Third, the workplace environment is not good
① workplace lighting is bad;
② temperature inappropriate, excessive noise;
③ equipment layout is unreasonable, as well as spare parts, semi-finished products piled irregular and the like;
④ process planning and process equipment do not meet safety requirements, the lack of necessary safety measures.
2015年11月13日星期五
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models reinforced straighten cutter leng...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models reinforced straighten cutter leng...: In order to achieve CNC steel models and thread steel straightening machine of numerical control, automation, accurate measurement must be ...
CNC steel models reinforced straighten cutter length detection
In order to achieve CNC steel modelsand thread steel straightening machine of numerical control, automation, accurate measurement must be reinforced according to the length of the required length automatically cut reinforcement. In this paper, these two questions relative error were studied, and in my school Machinery Factory production of steel straightening and cutting machine and achieved satisfactory results, cutting steel is less than 0.5%, to overcome the existing equipment can not be used for small-diameter steel tone straight and cutting question. The device has an automatic length detection, automatic synchronization of the mobile station under the knife, cut the number of steel automatic counting and other functions.
1, CNC steel modelsworks Figure 1 is reinforced straighten cutter of the mechanical drive schematic. It is transferred straight bars 1 in 2 and traction drive roller 4 feed rollers under a rotating tune straight 3 straight. Reinforced straight through after the upper and lower turret of the port to move forward. When the front end reinforcement after straightening iron is not moved to stop position 7, 8 hammer inertia wheel drive although mainly as vertical reciprocating movement 9, but due to not come into contact with the knife station 10, it is not subjected to shear reinforcement. When the front straight after the steel top to 7:00 stopper by the lever 6 causes the upper turret 10, lower turret 5 is moved forward. At this point, the reciprocating motion of the hammer 8 through the upper and lower turrets of reinforced shear (shear reinforcement length L), completed a steel straightening and cutting. Continuous motion, to complete the continuous steel straightening and cutting.
2, reinforced length detection CNC steel models harsh working conditions, larger vibration machines work. Upon detecting a bar size, in addition to ensuring accuracy, but also must meet anti-interference ability, reliable, long life and other requirements. Existing reinforced straighten cutter size detection machine adopts contact measurement, that is, when reinforced move, driven by resilient friction wheel rotation. Friction wheel and then connected with the pulse generator, calculate bar length by the count value of the pulse generator. Due to straighten cutter work in the machine itself and reinforced vibration is very strong, wear friction wheel is extremely serious, if from time to time to replace the friction wheel is detected, it will affect the detection accuracy, resulting in cutting errors. For these reasons, reinforced length detection method must be used for non-contact detection. By trials comparing the use of applied magnetic signal on reinforcement alternately programs more feasible, meet the design requirements.
1, CNC steel modelsworks Figure 1 is reinforced straighten cutter of the mechanical drive schematic. It is transferred straight bars 1 in 2 and traction drive roller 4 feed rollers under a rotating tune straight 3 straight. Reinforced straight through after the upper and lower turret of the port to move forward. When the front end reinforcement after straightening iron is not moved to stop position 7, 8 hammer inertia wheel drive although mainly as vertical reciprocating movement 9, but due to not come into contact with the knife station 10, it is not subjected to shear reinforcement. When the front straight after the steel top to 7:00 stopper by the lever 6 causes the upper turret 10, lower turret 5 is moved forward. At this point, the reciprocating motion of the hammer 8 through the upper and lower turrets of reinforced shear (shear reinforcement length L), completed a steel straightening and cutting. Continuous motion, to complete the continuous steel straightening and cutting.
2, reinforced length detection CNC steel models harsh working conditions, larger vibration machines work. Upon detecting a bar size, in addition to ensuring accuracy, but also must meet anti-interference ability, reliable, long life and other requirements. Existing reinforced straighten cutter size detection machine adopts contact measurement, that is, when reinforced move, driven by resilient friction wheel rotation. Friction wheel and then connected with the pulse generator, calculate bar length by the count value of the pulse generator. Due to straighten cutter work in the machine itself and reinforced vibration is very strong, wear friction wheel is extremely serious, if from time to time to replace the friction wheel is detected, it will affect the detection accuracy, resulting in cutting errors. For these reasons, reinforced length detection method must be used for non-contact detection. By trials comparing the use of applied magnetic signal on reinforcement alternately programs more feasible, meet the design requirements.
2015年11月10日星期二
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar construction Use Straightening M...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar construction Use Straightening M...: GT6-14A CNC Rebar construction Use: Debugging CNC hydraulic steel straightening machine is a critical step in the formal operation of th...
GT6-14A CNC Rebar construction Use Straightening Machine
GT6-14A CNC Rebar construction Use: Debugging CNC hydraulic steel straightening machine is a critical step in the formal operation of the device, future steel production process, has underestimated the role of, but the reality is that many enterprises in order to rush to production, one-sided pursuit of economic efficiency and not enough emphasis on this key measure, and then planted a lot of hidden dangers for the subsequent operation, here we explore simple steel straightening and cutting machine debugging requirements. Installation GT6-14A CNC Rebar, the first should be maintained on a relatively flat ground, it is best to put some cushion, you can prevent the machine at high speed when and ground vibrate. Host connectivity and the best runner on the same straight line, check whether the punch and bite off, if you do not bite it, adjust the height of the lower pulley to slide inside slider transferred to the desired size, and then use the screws fixed. When debugging GT6-14A CNC Rebar straighten opportunity to bend the wire phenomenon, you can adjust the angle of straight down the block to see if and straightening device, the pressure roll groove in a straight line. Yarn breakage encountered, we should first check to see if the straight block angle is too large, or the knife does not return back, spring wire roll on too loose, the material is not good and so on. When the machine has run wire phenomenon, related operations personnel necessary to check whether the pressure roller spring too tight, too loose tension spring slide, or slide below Ganggun dragline silk is not in place, the slide does not slide. In specific debugging GT6-14A CNC Rebar process, the operator should strictly check the electrical circuit wiring is correct, each operating point and stop control are normal and reliable. After straightening adjustments within straight rotations, with particular attention to the adjustment lock nut on the bolt without loosening, and close the safety cover, before starting the motor.
2015年11月6日星期五
Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine, the need for constructio...
Portable Cutting Machine，C42 Rebar Cutter，GQ40A Rebar Cutter: Portable cutting machine, the need for constructio...: What is Portable Cutting Machine ? In fact, it is cutting equipment, primarily for cutting steel, meets the requirements of the job. Many p...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models's precautions
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models's precautions: First, check CNC steel models mechanical performance is good, the table and the table to maintain the level bending machine; and ready for...
2015年11月5日星期四
CNC steel models's precautions
First, check CNC steel models mechanical performance is good, the table and the table to maintain the level bending machine; and ready for all kinds of mandrel tool block.
Second, according to the diameter and bending hoop machines installed rebar processing requirements mandrel forming axis, iron shaft gear or a variable fences, mandrel diameter should be 2.5 times the bar diameter.
Third, check the mandrel, the stopper, the turntable should be no damage and cracks, securing reliable shield, confirm normal machine operation by air before the operation.
Fourth, when the job will need to bend rebar inserted in one end of the fixed turntable with a gap, and the other end is fixed and hand pressed against the body, inspection body fixed, and indeed on the side of safety before starting block reinforcement.
Five non-replacement of jobs and change the angle of the mandrel and the governor and other operations, nor refueling or removal.
Sixth, bending steel, non-processed CNC steel models machines for the specified rebar diameter, root number and mechanical speed.
Seven high bending stiffness or low alloy steel, machinery nameplate should be a maximum limit for standard diameter, and replace the corresponding spindle.
Eight, prohibited within the operating radius of curved steel and the body does not have a fixed side stop people. Curved good semi-finished products should be stacked neatly, hooks shall not be upward.
Nine, turntable commutation, must be carried out after it stops.
Ten, the job is finished, clean up the site, maintenance CNC steel models, power lockbox
Second, according to the diameter and bending hoop machines installed rebar processing requirements mandrel forming axis, iron shaft gear or a variable fences, mandrel diameter should be 2.5 times the bar diameter.
Third, check the mandrel, the stopper, the turntable should be no damage and cracks, securing reliable shield, confirm normal machine operation by air before the operation.
Fourth, when the job will need to bend rebar inserted in one end of the fixed turntable with a gap, and the other end is fixed and hand pressed against the body, inspection body fixed, and indeed on the side of safety before starting block reinforcement.
Five non-replacement of jobs and change the angle of the mandrel and the governor and other operations, nor refueling or removal.
Sixth, bending steel, non-processed CNC steel models machines for the specified rebar diameter, root number and mechanical speed.
Seven high bending stiffness or low alloy steel, machinery nameplate should be a maximum limit for standard diameter, and replace the corresponding spindle.
Eight, prohibited within the operating radius of curved steel and the body does not have a fixed side stop people. Curved good semi-finished products should be stacked neatly, hooks shall not be upward.
Nine, turntable commutation, must be carried out after it stops.
Ten, the job is finished, clean up the site, maintenance CNC steel models, power lockbox
2015年5月24日星期日
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar
CNC steel prices
Introduction:
Rebar straightener and cutter is highly automatic, with fast traction speed and long working life. Bars straightened by it are with little strength loss, good straightness and no scratch. As an experience manufacturer in China, our CNC straightener for 14mm steel wire shares large national and international markets, due to its numerous features, such as easy operation, simple adjustment, outstanding blanking and high performance, etc.
Application:
Rebar straightener and cutter is designed to straighten and cut the architectural III cold rolling rebar, cold-rolled plain bar and hot rolling coiled round bar.
Features:
1. It adopts one-way hydraulic system, which ensures stable operation and low noise.
2. CNC straightener for 14mm steel wire is with high efficiency and fast straightening speed, due to its high power motor.
3. It has accurate cutting length and little material loss, and cutting error is reduced from ±2cm into ±1cm.
Specification:
Capacity Steel Rod Φ6-14mm
Rebar Φ6-12mm
Cutting Length 400mm to up
Cutting Error ±0.5cm
Speed 48-55m/min
Straighten & Traction Motor 11KW
Pump Motor 5.5KW
Voltage 380V/3phase
Straightening Degree ±2mm/m
Whole Weight 1200KG
Dimension(L×W×H)(mm) 2940×800×1100
Motor Optional 220V/415V/440V 50HZ/60HZ
Introduction:
Rebar straightener and cutter is highly automatic, with fast traction speed and long working life. Bars straightened by it are with little strength loss, good straightness and no scratch. As an experience manufacturer in China, our CNC straightener for 14mm steel wire shares large national and international markets, due to its numerous features, such as easy operation, simple adjustment, outstanding blanking and high performance, etc.
Application:
Rebar straightener and cutter is designed to straighten and cut the architectural III cold rolling rebar, cold-rolled plain bar and hot rolling coiled round bar.
Features:
1. It adopts one-way hydraulic system, which ensures stable operation and low noise.
2. CNC straightener for 14mm steel wire is with high efficiency and fast straightening speed, due to its high power motor.
3. It has accurate cutting length and little material loss, and cutting error is reduced from ±2cm into ±1cm.
Specification:
Capacity Steel Rod Φ6-14mm
Rebar Φ6-12mm
Cutting Length 400mm to up
Cutting Error ±0.5cm
Speed 48-55m/min
Straighten & Traction Motor 11KW
Pump Motor 5.5KW
Voltage 380V/3phase
Straightening Degree ±2mm/m
Whole Weight 1200KG
Dimension(L×W×H)(mm) 2940×800×1100
Motor Optional 220V/415V/440V 50HZ/60HZ
Relate Equipments/Accessories
2015年5月20日星期三
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar
Rebar straightener and cutter is highly automatic, with fast traction speed and long working life. Bars straightened by it are with little strength loss, good straightness and no scratch. As an experience manufacturer in China, our CNC straightener for 14mm steel wire shares large national and international markets, due to its numerous features, such as easy operation, simple adjustment, outstanding blanking and high performance, etc.
Rebar straightener and cutter is designed to straighten and cut the architectural III cold rolling rebar, cold-rolled plain bar and hot rolling coiled round bar.
1. It adopts one-way hydraulic system, which ensures stable operation and low noise.
2. CNC straightener for 14mm steel wire is with high efficiency and fast straightening speed, due to its high power motor.
3. It has accurate cutting length and little material loss, and cutting error is reduced from ±2cm into ±1cm.
Rebar straightener and cutter is designed to straighten and cut the architectural III cold rolling rebar, cold-rolled plain bar and hot rolling coiled round bar.
1. It adopts one-way hydraulic system, which ensures stable operation and low noise.
2. CNC straightener for 14mm steel wire is with high efficiency and fast straightening speed, due to its high power motor.
3. It has accurate cutting length and little material loss, and cutting error is reduced from ±2cm into ±1cm.
Relate Equipments/Accessories
GT4-12 CNC Rebar
As a recognized CNC rebar cutter supplier in China, our hydraulic straightening and cutting machine shares large market. It is applied to plain carbon steel, hot rolled steel rod and deformed steel bar of reinforced concrete. It can be widely used in construction industry, such as rebar process factories, road and bridge construction, highway construction, airport construction, railway construction and mine protection, etc.
1. Our CNC rebar cutter is with high efficiency and fast straightening speed.
2. It makes full use of material and has less material loss.
3. It is fully CNC control, easy to operate and maintain.
4. Hydraulic straightening and cutting machine is with competitive price and low energy consumption.
1. Our CNC rebar cutter is with high efficiency and fast straightening speed.
2. It makes full use of material and has less material loss.
3. It is fully CNC control, easy to operate and maintain.
4. Hydraulic straightening and cutting machine is with competitive price and low energy consumption.
2015年5月19日星期二
2015年5月18日星期一
2015年5月15日星期五
2015年5月14日星期四
2015年5月13日星期三
2015年4月12日星期日
2015年1月27日星期二
GT6-14A GT4-12 CNC CNC steel and reinforced practical use
CNC steel capable of continuous production of products of any shape, without the need for mechanical adjustment on; GT6-14A CNC reinforcement when fixing the bending angle does not need to interrupt processing. Compare the traditional process: CNC steel manufacturer stirrups traditional process generally use single coiled wire, modulated, cutting, bending hoop and distribution processes to achieve. GT6-14A NC reinforced its technology is lagging behind, unable to meet the needs of modern construction schedule, and just a lot of waste, occupy more space, more employment, low productivity, stirrups dimensional accuracy and shape accuracy is poor. GT6-14A CNC steel using advanced computer numerical control, automatic rapid completion of reinforced straighten, cut to length, bending hoop, cut. High efficiency machine, GT4-12 CNC reinforced steel workers can replace 20-30, is unique in the field of steel processing
GT4-12 CNC CNC steel and reinforced practical use?
CNC steel prices are set by the manufacturer in accordance with international standards, assessments made by imported servo motor drive, ensure steel straightening achieve the best accuracy. CNC steel manufacturers bending and shear mechanism: GT4-12 CNC reinforced by imported servo motor drive, high-speed rotation and bending arm stretching, shearing mechanism at high speed shearing action to ensure the accuracy of steel bending. Steel CNC control system: The machine uses foreign mature control system, high reliability. Reinforced GT4-12 CNC control system with fault identification and alarm functions. CNC steel manufacturers can design up to any type of ancient and modern graphics and contour shapes within 60 corners, and can be stored on a different product shapes thousands more, and a store graphics library, so many varieties of mass production.
订阅：
博文 (Atom)