图片
2015年12月15日星期二
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: GT6-14A CNC Rebar operation to seize the main poin...: GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation. ...
GT6-14A CNC Rebar operation to seize the main points
GT6-14A CNC Rebar working environment is very dangerous, so steel straightening machine operation must be strict, safe operation.
First, according to the bar diameter straight tone, choose the appropriate straightening block, entrainment wheel slots and drive speed. Straightening block aperture is larger than the bar diameter should be 2 ~ 5mm, the same width and the traction wheel straightening bar diameter.
Second, straightening adjustment block. Within the general tone straight five straight blocks, the first of two straight blocks 1,5 shall be placed in the line will be in the middle of the three may be offset from the centerline. First make steel offset about 3mm offset through test tone, such as reinforced still slow corners, gradually increase the offset until straightening up.
Third, cut three or four bars need to stop after checking the length is appropriate, subject to bias, adjustable limit switches or length plate, until the appropriate date.
Fourth, in the front portion of the guide tube should be installed about 1 meter steel one.Gt6-14a CNC Rebar should be transferred through the first pipe, and then penetrate the guide tube and transfer straight to prevent pop wounding nearly every dish reinforced straight when finished.
Fifth, the straightening block is not fixed, the shield is not covered before, can not penetrate reinforced in order to prevent the switch on the machine, straight block flying wounding.
Sixth, the machine allowed to pile up objects to prevent mechanical vibration objects have fallen into the body. Reinforced load pressure roller, hand drum should maintain a certain distance, the drum machine operation shall not be adjusted, non-gloved hands.
Seven, Gt6-14a CNC Rebar is not adjusted until the end, people have to avoid, prevent swinging wounding. Shorter than 2m or larger in diameter than steel straightening 9mm should low speed processing.
2015年12月12日星期六
GT6-14A CNC Rebar operator safety precautions
1.GT6-14A CNC Rebar must be operated by hand. The operator must go through specialized security knowledge assessment, certificates after passing the examination. Mechanical installation should be solid stable, horizontal position. Fixed machinery should be a reliable basis; when moving mechanical work wedged tight walking round.
2. Mechanical prohibited ill job, find fault must be immediately shut down, turn off the power, by a professional mechanical maintenance man responsible for maintenance must assign someone to monitor mechanical maintenance. You must set the anti-smashing, rain hangar beside the machine should have piled raw materials, semi venues.
3. Longer bars during processing, should be someone helping, and obey the command of the operator, shall be arbitrarily sliding.
4. Feeder, the trough should be installed straight, and should be aligned with the guide tube, and the lower knife adjusting centerline straight holes.
5. After applying hand turn the flywheel to check the drive mechanism and the working device, adjust the gap, tightening bolts, confirm normal, start air operation, and no abnormal noise should check the bearings, gears meshing well, after operating normally before the job.
6. Gt6-14a CNC Rebar Should straighten rebar diameter, choose the appropriate straightening blocks and transmission speed. Aperture straightening block should Reinforced big 2 ~ 5mm, transmission speed should be chosen depending on the diameter, larger diameter should use slow, after debugging qualified before feeding.
7. In straightening block is not fixed, the front shield cover shall not feed. The job is strictly prohibited open the protective cover and adjust the gap ministries.
8. When Gt6-14a CNC Rebar is fed, hand and drag wheel should maintain a certain distance, can not close.
9. Before feeding, should not straight steel tip resection. Guide tube should be installed before a 1m long steel pipe, steel pipe and then should be fed straight through the front of the guide hole.
2. Mechanical prohibited ill job, find fault must be immediately shut down, turn off the power, by a professional mechanical maintenance man responsible for maintenance must assign someone to monitor mechanical maintenance. You must set the anti-smashing, rain hangar beside the machine should have piled raw materials, semi venues.
3. Longer bars during processing, should be someone helping, and obey the command of the operator, shall be arbitrarily sliding.
4. Feeder, the trough should be installed straight, and should be aligned with the guide tube, and the lower knife adjusting centerline straight holes.
5. After applying hand turn the flywheel to check the drive mechanism and the working device, adjust the gap, tightening bolts, confirm normal, start air operation, and no abnormal noise should check the bearings, gears meshing well, after operating normally before the job.
6. Gt6-14a CNC Rebar Should straighten rebar diameter, choose the appropriate straightening blocks and transmission speed. Aperture straightening block should Reinforced big 2 ~ 5mm, transmission speed should be chosen depending on the diameter, larger diameter should use slow, after debugging qualified before feeding.
7. In straightening block is not fixed, the front shield cover shall not feed. The job is strictly prohibited open the protective cover and adjust the gap ministries.
8. When Gt6-14a CNC Rebar is fed, hand and drag wheel should maintain a certain distance, can not close.
9. Before feeding, should not straight steel tip resection. Guide tube should be installed before a 1m long steel pipe, steel pipe and then should be fed straight through the front of the guide hole.
2015年12月11日星期五
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models should be cleaned
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: CNC steel models should be cleaned: First, wash and clean-up. As a steel processing equipment, CNC steel models using undoubtedly will leave some residual steel scrap, so af...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Mechanical CNC steel models structure optimization...
CNC steel prices，CNC steel models，GT6-14A CNC Rebar，GT4-12 CNC Rebar: Mechanical CNC steel models structure optimization...: CNC steel models in the use of the urgent need to support the body as a machine, that is, roughly said body of steel bending machine. Coate...
2015年12月10日星期四
Mechanical CNC steel models structure optimization
CNC steel models in the use of the urgent need to support the body as a machine, that is, roughly said body of steel bending machine. Coated with a layer of special coating, not only beautify a good surface on the surface of the machine the machine, while the machine surface of the metal is a good protection.
Usually used when the machine needs to be well maintained, each time without the use of the residual trivial machine for cleaning above, guarantee the next time you use when not disturbed. In machine maintenance when the machine circuit checks, check the circuit breaker has no short circuit condition.
CNC steel models structure in the design were fully optimized, excellent principle guarantees the usual use of the machine, for the user, when using the machine need to follow relevant procedures and operating processes. in use when CNC steel models needs to pay attention to safety measures in place to avoid security risks.
Usually used when the machine needs to be well maintained, each time without the use of the residual trivial machine for cleaning above, guarantee the next time you use when not disturbed. In machine maintenance when the machine circuit checks, check the circuit breaker has no short circuit condition.
CNC steel models structure in the design were fully optimized, excellent principle guarantees the usual use of the machine, for the user, when using the machine need to follow relevant procedures and operating processes. in use when CNC steel models needs to pay attention to safety measures in place to avoid security risks.
2015年12月3日星期四
CNC steel models should be cleaned
First, wash and clean-up. As a steel processing equipment, CNC steel models using undoubtedly will leave some residual steel scrap, so after using the need to develop a good habit, it is timely for the various machines are devices to clean up. So as not to be disturbed in the future use of the process. At the same time when the device is not used to carry out the necessary cleanup is particularly important, including the use of necessary damp cloth with neutral detergent to clean the surface of the device, remove stains and dirt on top of the machine, to avoid the prolonged impact of the machine appearance and performance. In the clean-up time, especially for the interior of CNC steel models and a number of blind spots clean.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check CNC steel models is a regular process that requires a dedicated time to maintenance.
Circuit of maintenance and inspection is indispensable, starting from the machine's power switch is connected between each part of the machine until the motor, the traditional part of the operative part is not in place and so on. Check each part of the machine is not a fault, such as cracking, abrasion and other phenomena. In short, check CNC steel models is a regular process that requires a dedicated time to maintenance.
订阅：
博文 (Atom)